Ics Triplex T8311 以太网及串口通讯模块

Ics Triplex   T8311    以太网及串口通讯模块
Ics Triplex   T8311    以太网及串口通讯模块


罗克韦尔ICS Triplex   T8311  输出模块40通道数字24/48VDC 在某些操作和环境条件下，其中一个数字输出模块的电压轨可能会出现噪声。对这些电压轨进行采样，以确保它们在特定的公差范围内；但噪声偶尔会导致监控电路报告过电压，导致DO模块关闭。改进了内部滤波器，减少了噪音的影响，防止模块关闭。
罗克韦尔ICS Triplex  T8311
这些规则适用于此版本：
T8311（和T9120）处理器和Workbench必须来自同一产品版本（即R1.33）。
 工作台许可证：测试的版本是列表中的版本（在文档前面给出）。
 可以使用AADvance Workbench许可证R1.2及更高版本；早期的许可证版本不兼容。
AADvance 1.33是AADvance1.3版本的增量版本。这
发行说明包括以下关于AADvance的信息
版本1.33：
 此版本的硬件和软件构建
 系统增强功能
 已更正此版本中的问题和异常
 仍然适用的限制
 技术说明、产品通知和产品安全咨询
 产品兼容性规则
 技术支持和额外资源
此版本中包含以下增强功能。
 增加变量绑定内存
变量绑定（KVB）内存的大小已增加
从64 K增加到128 K。这将允许您增加
可以在中的控制器之间设置的变量绑定
应用
 适用于5个用户、无限控制器的新Workbench许可证
新的许可证选项T9084U可用：这是一个AADvance
适用于5个用户的工作台许可证，数量不受限制
控制器。它只能作为USB许可证选项使用：它可以工作
使用Windows XP Service Pack 3；Windows Vista；Windows 7和
32位和64位版本的Server 2003。
以下问题和异常情况已在本版本中得到纠正。
 数字输出模块关闭
在某些操作和环境条件下，噪音可能
数字输出模块电压轨之一的存在。这些
对电压轨进行采样，以确保它们在特定范围内
容忍但噪声偶尔会导致监控电路
报告过电压，导致DO模块关闭。
改进了内部过滤器，减少了
噪音并防止模块关闭。
 I/O初始化已暂停-TN30051-01（回答id 544046）
如果在控制器启动过程中发生I/O模块故障，则可能
停止I/O初始化。因此，控制器启动过程
未能完成，导致应用程序挂起。
已经对控制器启动进行了更改，以防止出现这种情况
防止发生。
 48模块配置的系统通电
AADvance支持的大I/O模块数
控制器为48。某些配置，特别是当
大多数是数字输出模块，可能导致系统
电源循环后正确启动。控制器的更改
已经进行了启动以防止这种情况发生。
 处理器失去同步
在双处理器配置中，在某些情况下是可能的
两个处理器失去同步的条件，但是
继续异步运行。尽管I/O仍然进入
在故障保护模式下，任何绑定数据都可能不正确。
已经对控制器进行了更改，以防止
发生。
 杂散软错误检测（SED）故障-TN30056-01
（答案id:564815）
每个AADvance模块使用一个或多个FPGA来提供
处理器和I/O之间的通信接口
模块。AADvance中使用的FPGA的制造商
发布了一个产品通知，标识此设备可以
错误地生成SED错误。FPGA制造商
已对控制器进行了建议的更改，以防止
这种情况不会发生。
 处理器在联机更新后失去同步
有可能对超过37的大型系统进行在线更新
安装的I/O模块可能会导致处理器丢失
同步。已对控制器进行了更改
防止这种情况发生。
 SNCP内核变量绑定（KVB）通信丢失
在某些条件下，双SNCP的两个链路都有可能
绑定配置失败。已对控制器进行了更改
为了防止这种情况发生
Rockwell ICS Triplex T8110C  Communications Interf module Under certain operating and environmental conditions noise can be present of one of the digital output module voltage rails. These voltage rails are sampled to ensure that they are within a specific tolerance; but the noise occasionally caused the monitoring circuit to report an over-voltage, resulting in the DO module shutting down. An internal filter has been improved that reduces the effect of the noise and prevents the module from shutting down.

Rockwell ICS Triplex T8110C

These rules apply to this release:

 T8110C (and T9120) processors and Workbench MUST be from the same Product Release (i.e. R1.33).

 Workbench licenses: the versions tested are those in the list (given earlier in the document).

 AADvance Workbench licenses R1.2 and later can be used; earlier license versions are not compatible.
AADvance 1.33 is an incremental release of AADvance Release 1.3. This
Release Note includes the following information about AADvance
Release 1.33:
 Hardware and Software Builds for this Release
 Enhancements to the System
 Corrected Problems and Anomalies in this Release
 Restrictions that still Apply
 Tech Notes, Product Notices and Product Safety Advisories
 Product Compatibility Rules
 Technology Support and Additional Resources

The following enhancements are included in this release.
 Increase Variable Bindings Memory
The Variable Bindings (KVB) memory has been increased in size
from 64 K to 128 K. This will allow you to increase the number of
variable bindings that you can set up between controllers in an
application.
 New Workbench license for 5 Users, Unlimited Controllers
New license option T9084U is available: this is an AADvance
Workbench license for 5 Users and no limit to the number of
controllers. It is only available as a USB license option: it will work
with Windows XP Service Pack 3; Windows Vista; Windows 7 and
Server 2003 in both 32-bit and 64-bit versions.

The following problems and anomalies have been corrected in this release.
 Digital Output Module Shutting Down
Under certain operating and environmental conditions noise can be
present of one of the digital output module voltage rails. These
voltage rails are sampled to ensure that they are within a specific
tolerance; but the noise occasionally caused the monitoring circuit to
report an over-voltage, resulting in the DO module shutting down.
An internal filter has been improved that reduces the effect of the
noise and prevents the module from shutting down.

 I/O initialization stalled - TN30051-01 (answer id. 544046)
If, during a controller start-up an I/O module failure occurs it can
stop the I/O initialization. As a result, the controller start-up process
fails to complete, leaving the application program suspended.
Changes to the controller start-up have been made that prevents this
from occurring.
 System power up with a 48 module configuration
The maximum number of I/O modules supported by an AADvance
controller is 48. Certain configurations, particularly when the
majority is Digital Output Modules, can result in a system not
starting-up correctly after a power cycle. Changes to the controller
start-up have been made to prevent this from occurring.
 Processor loss of synchronization
In dual processor configurations it was possible under certain
conditions for the two processors to lose synchronization, but
continue to run asynchronously. Although the I/O still went to its
fail-safe mode, it was possible for any binding data to be incorrect.
Changes to the controller have been made to prevent this from
occurring.
 Spurious Soft Error Detection (SED) faults - TN30056-01
(answer id: 564815)
Each AADvance module uses one or more FPGA's to provide the
communication interface between the processor and the I/O
modules. The manufacturer of the FPGA used in AADvance
released a Product Notification identifying that this device could
spuriously generate SED errors. The FPGA manufacturers
recommended changes have been made to the controller to prevent
this from occurring.
 Processors lost synchronization after an on-line update
It is possible that on-line updates to a large system with more than 37
I/O modules installed can cause the processors to lose
synchronization. Changes to the controller have been made to
prevent this from occurring.
 Loss of SNCP Kernel Variable Bindings (KVB) communication
Under certain conditions it was possible for both links of dual SNCP
bindings configuration to fail. Changes to the controller have been
made to prevent this from happening






其他相关型号：

ICS TRIPLEX	T9100		ICS TRIPLEX	T8310
ICS TRIPLEX	TC-801-02-4M5		ICS TRIPLEX	T8300
ICS TRIPLEX	TC-305-01-5M0		ICS TRIPLEX	T8231
ICS TRIPLEX	TC-303-01-2M0		ICS TRIPLEX	T8193
ICS TRIPLEX	TC-301-02-2M0		ICS TRIPLEX	T8191
ICS TRIPLEX	TC-215-01-6M5		ICS TRIPLEX	T8160
ICS TRIPLEX	TC-215-01-4M5		ICS TRIPLEX	T8151B
ICS TRIPLEX	TC-201-01-6M5		ICS TRIPLEX	T8110C
ICS TRIPLEX	TC-201-01-4M5		ICS TRIPLEX	T8110B
ICS TRIPLEX	T9481		ICS TRIPLEX	T8100
ICS TRIPLEX	T9451		ICS TRIPLEX	9852*4 cable
ICS TRIPLEX	T9432		ICS TRIPLEX	9852*4
ICS TRIPLEX	T9402		ICS TRIPLEX	9852*3 cable
ICS TRIPLEX	T9310-02 PN-175486		ICS TRIPLEX	9852*3
ICS TRIPLEX	T9310-02		ICS TRIPLEX	9852*2/9832*1
ICS TRIPLEX	T9110		ICS TRIPLEX	9852*1/9802*2 cable
ICS TRIPLEX	T8480C		ICS TRIPLEX	9852*1/9802*2
ICS TRIPLEX	T8461		ICS TRIPLEX	9852*1
ICS TRIPLEX	T8451		ICS TRIPLEX	9852*1/9802*2
ICS TRIPLEX	T8431C		ICS TRIPLEX	9832*3 cable
ICS TRIPLEX	T8431		ICS TRIPLEX	9832*2 cable
ICS TRIPLEX	T8403C		ICS TRIPLEX	9802*3 cable
ICS TRIPLEX	T8403		ICS TRIPLEX	9802*1/9852*2 cable
ICS TRIPLEX	T8314		ICS TRIPLEX	9802*3/9832*1 cable
ICS TRIPLEX	T8312-4		ICS TRIPLEX	151661 4013-2255
ICS TRIPLEX	T8311		ICS TRIPLEX	1433/09232486825