Vibro-meter 200-560-000-018 200-560-101-015 VM600 IOC4T 通信接口模块
Vibro-meter 200-560-000-018 200-560-101-015 VM600 IOC4T 通信接口模块
VM600 Mk2 / VM600 XMV16 + XIO16T振动监测模块
VM600 Mk2 /VM600 XMV16 + XIO16T振动状态监测模块提供16个动态通道和4个转速计（速度）通道，均可独立配置。
VM600 Mk2 /VM600 XMV16 + XIO16T振动监测模块提供16个动态通道和4个转速计（速度）通道，均可独立配置。
主要特征
16 个动态通道和 4 个转速计通道
每个动态通道和每个双通道多 20 个处理输出（每个 XMV16 12 个）
通过异步（固定频率）或同步（顺序跟踪）采样在所有通道上同时采集数据
24 位数据采集，高信噪比数据处理，高分辨率 FFT 每 500 毫秒高达 6400 行
每个动态通道和转速计通道的差分信号输入
设计用于与 VibroSight® 软件一起运行：一个以太网连接器 (8P8C (RJ45)) 用于与 VibroSight 通信
可用模块
VM600 Mk2 /VM600 XMC16 + XIO16T 燃烧状态监测模块
VM600 Mk2 /VM600 XMV16 + XIO16T 振动状态监测模块
相关产品
VM600 IRC4智能中继卡
●额外的继电器，由来自MPC4和/或AMC8卡的多达86个输
入的方程式驱动，用于需要更复杂的逻辑(例如2oo3表决)时
●8个继电器可配置为8个SPDT或4个DPDT
●使用IRC4 Configurator软件可完全配置软件
●继电器可配置为正常通电(NE)或正常断电(NDE)，具有可配置的延迟
●螺丝端子连接器上提供所有继电器触点
VM600 IOC4T卡压降适配器
●4个可单独配置的通道,用于入I0C4T动态通道和转速计通道输
●降低通道的传感器电源输出电压
●-27V 输入至-24 V输出，-27V输入至-18 V输出或每通道直通连接
●当IOC4T传感器电源输出连接到第三方前端时减少外部电路和接线
用于VM600 I0C4T卡的
电容耦合适配器
●4个可单独配置的通道， 紆IOC4T缓冲(原始)传感器输出
●AC耦合通道的缓冲(原始)传.感器输出信号并去除DC分量
●每个通道1 μF串联电容器或直通连接
●当IOC4T卡的缓冲(原始)传.感器输出连接到测试和测量设备时，减少外部电路和布线
用于AMC8卡的VM600 I0C8T输入/输出卡
●AMC8卡的输入/输出(接口)卡-支持8个温度或过程监控通道
●每个监控通道的可配置信号输入和电流源输出
●每个监控通道的直流输出可配置为基于电流的信号(4 至20mA)或基于电压的信号(0至10 V)
●4个可配置继电器，每个继电器具有三个触点，以吸警报复位(AR)和危险旁路(DB)控制输入
VM600 Mk2/VM600 XMV16+XIO16T vibration monitoring module
The VM600 Mk2/VM600 XMV16+XIO16T vibration status monitoring module provides 16 dynamic channels and 4 tachometer(speed)channels,which can be configured independently.
The VM600 Mk2/VM600 XMV16+XIO16T vibration monitoring module provides 16 dynamic channels and 4 tachometer(speed)channels,which can be configured independently.
Main features
16 dynamic channels and 4 tachometer channels
Up to 20 processing outputs per dynamic channel and each dual channel(12 per XMV16)
Collect data simultaneously on all channels through asynchronous(fixed frequency)or synchronous(sequential tracking)sampling
24-bit data acquisition,high signal-to-noise ratio data processing,high resolution FFT up to 6400 lines per 500 milliseconds
Differential signal input for each dynamic channel and tachometer channel
Designed to work with VibroSight®The software runs together:an Ethernet connector(8P8C(RJ45))is used to communicate with VibroSight
Available modules
VM600 Mk2/VM600 XMC16+XIO16T combustion status monitoring module
VM600 Mk2/VM600 XMV16+XIO16T vibration status monitoring module
Related products
VM600 IRC4 smart trunk card
●Additional relays,consisting of up to 86 outputs from MPC4 and/or AMC8 cards
The input equation is driven when more complex logic(such as 2oo3 voting)is required
●8 relays can be configured as 8 SPDTs or 4 DPDTs
●Use IRC4 Configurator software to fully configure the software
●The relay can be configured as normal power-on(NE)or normal power-off(NDE)with configurable delay
●All relay contacts are provided on screw terminal connector
VM600 IOC4T card voltage drop adapter
●Four independently configurable channels for input to I0C4T dynamic channel and tachometer channel
●Reduce the sensor power output voltage of the channel
●-27V input to-24 V output,-27V input to-18 V output or pass-through connection per channel
●Reduce external circuits and wiring when the IOC4T sensor power output is connected to the third party front end
For VM600 I0C4T card
Capacitive coupling adapter
●4 individually configurable channels,with IOC4T buffered sensor output
●Buffered transmission of AC coupling channel.Sensor output signal and DC component removal
●Each channel 1μF series capacitor or through connection
●When the buffered(original)sensor output of the IOC4T card is connected to the test and measurement equipment,reduce the external circuit and wiring
VM600 I0C8T input/output card for AMC8 card
●Input/output(interface)card of AMC8 card-support 8 temperature or process monitoring channels
●Configurable signal input and current source output of each monitoring channel
●DC output of each monitoring channel can be configured as current-based signal(4 to 20mA)or voltage-based signal(0 to 10 V)
●Four configurable relays,each with three contacts,to absorb alarm reset(AR)and hazard bypass(DB)control inputs
Machinery protection module MPC4Mk2 + IOC4Mk2
Designed to operate with the second generation of VM600Mk2 rack-based machinery protection system.
The MPC4Mk2 + IOC4Mk2 module consists of processing and input/output (interface) modules that provide 4 dynamic and 2 auxiliary channels of machinery protection and optional condition monitoring in VM600Mk2 systems.
High-quality, high-reliability 19″ 6U rack for housing VM600Mk2/VM600 rack-based machinery monitoring systems. With space for up to 12 machinery monitoring cards (machinery protection, condition monitoring and/or combustion monitoring), up to 2 power supplies (for power supply redundancy) and a rack controller and communications interface card, and a power supply check relay. Robust aluminium construction suitable for use in harsh environments.
Features
- VM600Mk2 and VM600 system racks to house machinery protection and/or condition monitoring systems
- Robust aluminium construction
- Space for up to two RPS6U rack power supplies (AC-input and/or DC-input) to support rack power supply redundancy
- Space for up to 12 processing cards and power supply check relay
- Available in a version with mounting brackets positioned at the rear of the rack, and in a conformally coated version
其他相关型号：
Vibro-meter 200-510-070-113 200-510-111-034 VM600 MPC4
Vibro-meter 200-510-071-113 200-510-111-034 VM600 MPC4
Vibro-meter 200-560-000-016 200-560-101-015 VM600 IOC4T
Vibro-meter 200-560-000-018 200-560-101-015 VM600 IOC4T
Vibro-meter 200-560-000-113 200-560-101-017 VM600 IOC4T
Vibro-meter 200-566-000-012 200-566-101-012 VM600 IOCN
Vibro-meter 200-595-031-111 VM600 CPUM
Vibro-meter 200-595-100-014 200-595-072-122 VM600 CPUM
Vibro-meter 444-680-000-511
Vibro-meter 600-003 620-001-001-116 VM600 XMV16
Vibro-meter 620-002-000-113 620-003-111-112 VM600 XI016T
Vibro-meter 620-002-000-113 620-003-111-112 VM600 XIO16T
Vibro-meter VM600 200-510-041-021 200-510-111-021 MPC4
Vibro-meter VM600 200-560-000-114 200-560-101-018 IOC4T
Vibro-meter VM600 ABE040
Vibro-meter VM600 CMC16
Vibro-meter VM600 IOC16T
Vibro-meter VM600 IOC4T
Vibro-meter VM600 MP C4
Vibro-meter VM600 RPS6U
Vibro-meter VM600 RPS6U 200-582-500-013
Vibro-meter VM600 RPS6U配件113-40060
Vibro-meter VM600-ABE040 204-040-100-011
WINGREEN IPB PCB V2.0_A01 03ZSTL6-00-201-RS
WINGREEN IPB PCB V2.0_A01 03ZSTL6-00-201-RS
WINGREEN FAN_DETECTION V1.0_A05 03ZSTJ3-00-105
WINGREEN DUDT_DETECTION_V2.0_A01 03ZSTJ0-00-201-RS
WINGREEN PUIM V2.0 034STM4-00-200-RS
WINGREEN CANopen_ADAPTER V5.0_A01 03ZSTI-00-501-RS
WINGREEN DSPB_V4.0_A02 03ZSTI7-00-402-RS
WINGREEN FPB_V3.0_A01 03ZSTJ1-00-301-RS
WINGREEN ATKB_V5.0_A01 03ZSTI4-00-501
WINGREEN ATKB_V5.0_A01 03ZSTI4-01-501
WINGREEN LAIB V3.0_A00 034STN1-00-300-RS
WINGREEN LAIB V3.0_A00 034STN1-01-300-RS
WINGREEN FAN_DETECTION V1.0_A05 03ZSTJ3-00-105
WINGREEN LAIB V3.0_A00 034STN1-01-300-RS
WINGREEN FPB_V3.0_A01 03ZSTJ1-00-301-RS
WINGREEN ATKB_V5.0_A01 03ZSTI4-00-501
WINGREEN ATKB_V5.0_A01 03ZSTI4-01-501
WINGREEN DSPB_V4.0_A02 03ZSTI7-00-402-RS
客服1